AudioSource Speaker 2-Way In-Wall Speaker User Manual

0

Out of 0 Ratings

Owner's of the AudioSource Speaker 2-Way In-Wall Speaker gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 4
 
3
Tighten all six of the mounting screws in the same
manner until the speaker is properly aligned and held
tight to the wall surface. Caution: Do not over tighten!
Aiming the Tweeter
Carefully place your fingertips at the plastic edges of
the tweeter housing.
Using gentle pressure, swivel the tweeter to aim the axis
of the tweeter toward the listening area. You can use a
piece of music with a solid center-imaged vocalist to
assist in correctly aiming the tweeter. When the
tweeters are properly aligned, you will hear a coherent
and stable center image from your listening position.
Usually, it is sufficient to aim the tweeter only as it
handles the frequencies that control the direction of
individual sounds in your audio program material.
Next make sure that the clamps are positioned inside
the frame of the speaker.
With the grill removed, place the speaker in the wall
opening. Make sure that the speaker wire is not hanging
against the speaker where it can vibrate and rattle as the
speaker reproduces your music.
Next, one at a time, turn
each of the six screws
that operate the clamps
counter clockwise a few
turns until you feel the
clamp is loose from its
resting position. Now turn
the screw clockwise until
you feel the clamp contact
the wall surface.
Correct
Incorrect
1
2
3 4
5
6
Recommended Speaker Wire Gauges
The resistance of the speaker wire in your installation
can cause your speakers to perform at less than their
optimum quality level. Excess resistance caused by
using an undersized speaker wire can result in loss of
detail and definition in the bass region of your audio
program, as well as loss of dynamic range. Over
extremely long wire runs you may even experience a
loss of high frequency content in the audio signal.
50’ or less - 16 Gauge 2-Cond. CL3 Rated
50’ - 150’ - 12 Gauge 2-Cond. CL3 Rated
150’ - 200’ - 10 Gauge 2-Cond. CL3 Rated
To prevent sonic degradation in your AC Series
speaker installation, total speaker wire resistance
should be kept below 0.5 ohms. The following table
lists recommended speaker wire gauge versus wire
run length.
Painting the Speaker
Two paint shields are included in each AC Series
speaker package. Place the paint shield inside the
frame to protect the speakers. You can now safely
paint the speaker frames to match your wall surface
if you desire.
When painting the grill caution should be taken to
ensure that paint does not clog or congest the
perforated openings in the grill. This would prevent
proper operation of the grill by restricting the airflow
from the individual drivers in the speaker.
Removing the AC Series Speaker
Should it ever become necessary to remove the AC
Series speaker from the wall, simply remove the
grill and turn the six mounting screws counter-
clockwise until you feel the clamps lock out of position
in their resting flange. The speaker should easily
come out of the wall for service or replacement.
Locate a small hook tool
(available at most auto parts
stores or home improvement
shops, resembling a dentist’s
pick- a bent paper clip or
stiff wire will work as well),
hook the metal mesh of the
grill near a corner or edge
and gently pull it towards you.
Only lift the grill 1/4" (6mm) at
this location. Move the tool
1-2" (25-50mm) and repeat
until the grill can be removed
without damaging it (Figure 6).
Grill Removal (if installed)
Figure 6
Press
Here
Press Here
Press Here
Press
Here
(+)
(-)

   Find Your Products By Category