INSTEON Home Security System INSTEON Home Security System User Manual

0

Out of 0 Ratings

Owner's of the INSTEON Home Security System INSTEON Home Security System gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 4
 
2452-222/2452-422/2452-522 Rev. 11/6/2012 1:27 PM / See Owner’s Manual for Warranty Information.
Protected under U.S. and foreign patents (see www.insteon.com)
© Copyright 2012 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845
Sensor won’t control
linked responders
a) Make sure LED flashes to confirm it has power and is sensing motion
b) Sensor is in night-only mode (and it is “day”)
c) Move a dual-band INSTEON device (e.g., Access Point) closer to the Motion Sensor
d) Sensor is in its 1 minute countdown
LED flashing rapidly
after motion is
detected
Sensor did not receive an acknowledgement from one or more linked devices. If this occurs
repeatedly you may need to move a dual-band INSTEON device closer to the Sensor or you may
need to unlink a device which is no longer in use in your home. If the INSTEON responders are no
longer available, you may either use software or perform a factory reset to remove the unwanted links.
LED not flashing
upon motion
a) You may need to wait up to 8 seconds to see the flash
b) Battery may need to be replaced
Not sensing motion
a) Light detected and unit is in night-only mode
b) Motion Sensor aimed too low
c) Temperature too high, or low (sensor needs to be able to distinguish between what is being sensed
and its surroundings
d) See Placement Tips section
LED is double
flashing upon motion
Low battery warning—replace with fresh battery
Remove Motion Sensor as a Controller
1) Press and hold the set button on Motion Sensor for 5 seconds
Motion Sensor LED (behind sensor lens) will start blinking red
2) Press and hold the set button on Motion Sensor for 5 seconds
Motion Sensor LED will continue blinking red
3) Press and hold the responder set button until it beeps
Motion Sensor LED will stop blinking
4) Test by tapping the set button on Motion Sensor
Former responder will not respond
Factory Reset
Return Motion Sensor to Factory Settings
1) If possible, remove Motion Sensor as a controller of all responders before proceeding*
2) Remove battery
3) Wait 15 seconds
4) While pressing the set button, reattach the battery
After about 2 seconds the LED will turn on
5) Continue pressing the set button for 5 seconds and then release the set button.
The LED will turn off after about 2 seconds
* If you do not unlink, your responder will to continue to respond to Motion Sensor even after factory reset procedure is complete.
Owner’s Manual and Tech Support
For the most up-to-date Quick Start Guide visit http://www.insteon.com/support
Call: INSTEON Support Line at 866-243-8022
FCC and IC Warnings
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a
transformer-supplied appliance. Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres materiels, ne
pas installer pour commader une prise, un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.

   Find Your Products By Category